NC Rollbar Installation

Installations instructions for MonsterFlow intakes, Big Brake Kits, shocks and more.
phm14
Posts: 7
Joined: Wed Oct 28, 2009 12:46 pm

Post by phm14 »

Any common rattle can colors that work well for touchup?
Brian
Site Admin
Posts: 11307
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Post by Brian »

The black is a standard gloss black. The silver was an attempt to match the factory "sunlight silver" for 06+
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
tomkk
Posts: 23
Joined: Tue Dec 16, 2008 8:37 pm
Location: Port Orange, Fl

Post by tomkk »

Installed my Double Hoop roll bar with removable rear supports. I love the double hoop roll bar. I was afraid it's extra height was going to look strange with the top down but it looks great, the top easily clears it going up and down and seems very sturdy and well made. It adds enough height so I can get under the broomstick. I used the instructions here in the forum and just have a few things to pass on.

The trim & old style bars came out easily but the soft top hinge bracket prevented the roll bar from sliding in place. Loosening the two bolts holding the bracket in place allowed it to slightly, enough to let the slide into place. The picture shows the the two bolts on the passenger side just aft of the rear door post. Do the same on the driver's side. Be sure to re-tighten the bolts after the install is complete.
Image

Despite the "never a need to grind or drill out the holes" in the instructions, there was no way mine was going in without a bit of grinding the base holes. The bar was simply too rigid for me to move it even slightly. Only a very small amount of grinding but I still felt guilty ...

The kit with the rear supports includes two beefed up supports that install in the trunk. The 2nd picture in the May 17, 2009 post shows the prototype brace with the the optional cross brace - thought I'd toss in a couple of pics of the real braces.
Image
Image

The two braces went in easily but the bottom factory bolt on each side was too short and they had to be replaced with longer bolts. It would have been a nice touch to include those longer bolts (and the 4 shorter bolts id'd in step 10) in the install hardware package. I forgot to record the bolt sizes and lengths to put here so you can get them in advance. Sorry ...

My 2008 GT has rear speakers. It sounds from the forum like the single hoop bar has been upgraded to include the speaker mount studs but the double hoop bar hasn't. I drilled and tapped the square horizontal bar to mount the speakers but I actually ended up leaving the speakers out anyway.

The 1" holes that are the receivers for the removable rear support bars really need plugs of some sort to make them look better. I found some 1" and 7/16" (for the front holes) black nylon plugs at Lowe's that seem like they'll do the trick. Not sure whether vibration will gradually work them out or not but we'll see. Lowe's also had some chrome metal plugs that might work for the silver roll bar. Look in the small boxes where they have the specialty fasteners.

Trimming and reinstalling the plastic trim was a real PITA. Maybe I'm just slow with things like that but it easily took me twice as long to trim and reinstall the trim as the roll bar itself. Not really hard, just a lot of trial cutting and fitting. I wanted to save as much storage space as I could so I trimmed the small cubbys behind the driver and passenger seats to fit around the inner roll bar legs. Here's a picture of the passenger side.
Image

The only real problem I had was with the rear supports. The hole in the hoop and the part of the support bar that inserts into the hole are clearly made to fairly close tolerances. That might have been OK except the insides of the holes were then powder coated - couldn't get the supports into the holes without cleaning out the holes and then some. The more serious problem was the holes in the support base didn't align with the holes in the car body - the holes in the support base were about 1/8" aft of the holes in the body. No way the screws were going to fit. I tried loosening the rollbar to try to shift it forward a bit but no go - this bar fits very well into the car and there's just no play. I ended up grinding down the collar on the roll bar where marked in the picture to shift the support bar forward.
Image
I didn't have to get into the weld, just the collar that protrudes. The support bar that goes into those holes has to be shortened a corresponding amount. That shifted the support bar forward but not quite enough and I had to enlarge the holes in the support base to get the screws in. In addition, the rear of the support base had to be ground down to clear the trunk when it opened. Finally, the passenger side support base was not aligned correctly. You can see from the picture that it's cocked slightly counter clockwise.
Image
That twist misaligned the holes with the body holes . Not sure why this happened. Considering the geometry of the roll bar and support bars, I don't see how the installation could cause it. Anyway, there's nothing to do here except grind or drill out the hole enough to achieve sufficient alignment.

As I said before, I think the bar is great and I'm very happy with it. Here are some additional pics of the install.

Center support plates welded and primed:
Image
and driver's side attachment:
Image
The passenger side attachment:
Image
and the completed install:
Image
Some pictures of the completed install:
Image
Image
Image
Image
Tom
2008 Red GT soft top
whptgud
Posts: 30
Joined: Mon Nov 24, 2008 11:13 am

Post by whptgud »

Tom, thanks for the nice write up. Did you happen to weigh the new vs old bar?
TIA...
06 GT GG, PSS10, Hotchkis, GWR exhaust, RPF1, AD08, IL braces, MS, dptune
91 A CR 5sp, Millen, FM, GAB, MOMO, Panasport, Naca, braced
tomkk
Posts: 23
Joined: Tue Dec 16, 2008 8:37 pm
Location: Port Orange, Fl

Post by tomkk »

whptgud wrote:Tom, thanks for the nice write up. Did you happen to weigh the new vs old bar?
TIA...
Darn, I knew I was forgetting something. I meant to do that and I totally forgot. It'll be more than a little bit, though. 2" pipe vs 1", a beefy cross bar and the extra center legs that extend below the cross bar not to mention the extra rear supports. Sorry ...
Tom
2008 Red GT soft top
Brian
Site Admin
Posts: 11307
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Post by Brian »

Thanks Tom for the great write-up AND pics. No doubt future installers will much appreciate your additional details.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
jetkins
Posts: 7
Joined: Sun Jan 17, 2010 7:27 pm
Location: Austin, TX

Post by jetkins »

papdoc wrote:My double hoop roll bar arrived on Monday and I installed it yesterday. There are some notes on the installation instructions:
1. For the cars with the Bose Sound System: the new roll bar had the necessary holes predrilled for the installation of the speakers. These holes were missing in the previous versions of the rollbar, but obviously Brian took care of i
On the double-hoop bar, perhaps, but the single-hoop bar I received last week did not have holes or studs for mounting the speakers (or the Bluetooth module which bolts up in almost the same place on my '09 GT). It wasn't that big of a deal to drill holes and mount them with self-tappers, but I was disappointed to find that this still hasn't been fixed on the single-hoop bar over a year after it was resolved on the double.
tomkk
Posts: 23
Joined: Tue Dec 16, 2008 8:37 pm
Location: Port Orange, Fl

Post by tomkk »

My double hoop with rear supports didn't have the mounting holes either. I drilled and tapped the 3 holes but ended up leaving the speakers out anyway. The double hoop's extra center legs interfere with the cubbies behind the driver and passenger seats. Between the cubbies, the rollbar legs, the speakers (which protrude from their mount) and the center console lips the rear trim has to fit under, I figured something was going to break if I tried it with the speakers mounted. Frankly, I haven't missed the rear speakers a bit ...
Tom
2008 Red GT soft top
Roger
Posts: 4
Joined: Wed Oct 08, 2008 9:15 am
Location: Knoxville Tennessee
Contact:

double hoop rool bar weight

Post by Roger »

I am also installing the double hoop bar (silver) in my Red 07. regarding the question on new bar's weight: it is 30 pounds, which is 12 pounds heavier than factory bar, and as tomkk mentioned - it looks great and is impressive!
Roger
Roger
2007 Red Touring MT6 LSD, 235/40 T1Rs on 8" Enkei , Eibach sways, AEM CAI, Roadster Sport2 exhaust, MS airdam
tomkk
Posts: 23
Joined: Tue Dec 16, 2008 8:37 pm
Location: Port Orange, Fl

Post by tomkk »

Thx Roger. Did that weight include the rear support bars?
Tom
2008 Red GT soft top
Post Reply