Going with the Fighter, sliders, and Brian's NC seat mounts.
How do I "trick" the airbag sensors?
Replacing Miata NA/NB/NC Seats with Sparco
Replacing Miata NA/NB/NC Seats with Sparco
'06 MX-5 Sport 6-speed
Autocross junkie!
Autocross junkie!
Re: Replacing NC seats with Sparco
there's a resistor that you can put across the terminals on the connector. Not sure what the ohmage is, sorry. I know that it was discussed on miata.net.
OTOH my solution to the airbag light is a piece of black tape over the warning light.
OTOH my solution to the airbag light is a piece of black tape over the warning light.
2006 NC, Copper Red
2.3L, BEGi Turbo, Enthuza 3".
2.3L, BEGi Turbo, Enthuza 3".
Re: Replacing NC seats with Sparco
HA! Thanks, George.
Brian, I just placed an order for the seat rails.
Brian, I just placed an order for the seat rails.
'06 MX-5 Sport 6-speed
Autocross junkie!
Autocross junkie!
Re: Replacing NC seats with Sparco
Thanks for the order Chris.
BTW, I am another member of the infamous 'black tape club.'
BTW, I am another member of the infamous 'black tape club.'
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 5
- Joined: Sun Sep 12, 2010 6:09 pm
Re: Replacing NC seats with Sparco
I found this old topic, and need to add to it.
On a NC, I saw someone installed a Sparco seat. I have a new 2010 NC, and have a set of quite new Corbeau Fit pro seats (used in the recently sold NA), with corbeau supplied slider setup. I know the sliders/rails won't work in the NC, but what about the seats? Anyone have aftermarket seats, and if so, how is the clearance (head room) for a helmet. I know the twin OEM hoops are too low, but I might be going after a real roll bar, but don't know if those seats will even fit. Any knowledge here.
eddie
On a NC, I saw someone installed a Sparco seat. I have a new 2010 NC, and have a set of quite new Corbeau Fit pro seats (used in the recently sold NA), with corbeau supplied slider setup. I know the sliders/rails won't work in the NC, but what about the seats? Anyone have aftermarket seats, and if so, how is the clearance (head room) for a helmet. I know the twin OEM hoops are too low, but I might be going after a real roll bar, but don't know if those seats will even fit. Any knowledge here.
eddie
Re: Replacing NC seats with Sparco
Chris,
How did the Sparco Fighters fit? How difficult was the installation? Any idea how much Brian's mounts, plus sliders, plus sidemounts weigh? (I have a minimum weight for seats, including mounts, in my class.) Any photos?
How did the Sparco Fighters fit? How difficult was the installation? Any idea how much Brian's mounts, plus sliders, plus sidemounts weigh? (I have a minimum weight for seats, including mounts, in my class.) Any photos?
2009, STR & DD. 1995, HPDE. 2004 MSM, sold. 2010 Mazda3, hers.
Re: Replacing NC seats with Sparco
The Sparco Fighter seats, sliders, hardware, and Goodwin mounts weigh right at 30 lbs. Since this seat is a bottom mount, I had to add some steel strap to bridge the sliders. The sliders are mounted directly to the Goodwin piece, and I mounted the seats offset to the center of the car to ensure the driver's seat lined up with the pedals and the doors don't touch the shoulders of the seat (1/4" gap). I'll get some pics once I get my camara repaired.
'06 MX-5 Sport 6-speed
Autocross junkie!
Autocross junkie!
Re: Replacing NC seats with Sparco
Chris,
Thanks for the info. I'm planing to swap seats during the offseason, so I look forward to your photos.
Michael
Thanks for the info. I'm planing to swap seats during the offseason, so I look forward to your photos.
Michael
2009, STR & DD. 1995, HPDE. 2004 MSM, sold. 2010 Mazda3, hers.
Re: Replacing NC seats with Sparco
Chris,
Have you had a chance to take any photos?
Michael
Have you had a chance to take any photos?
Michael
2009, STR & DD. 1995, HPDE. 2004 MSM, sold. 2010 Mazda3, hers.
Re: Replacing NC seats with Sparco
Will do so this weekend as I'm reinstalling my radio & amp, along with my muffler and trailer hitch.
BTW - we were just under 2400 lbs at SCCA Nationals this year, with the A/C still installed and working, plus stock flywheel, brakes, and exhaust (manifold and midpipe were stock this year, but we took off the Mazdaspeed can). My car is really a STR car running R-comp tires.
BTW - we were just under 2400 lbs at SCCA Nationals this year, with the A/C still installed and working, plus stock flywheel, brakes, and exhaust (manifold and midpipe were stock this year, but we took off the Mazdaspeed can). My car is really a STR car running R-comp tires.
'06 MX-5 Sport 6-speed
Autocross junkie!
Autocross junkie!