Teaser Pics from Tom Suddard of Grassroots Motorsports Magazine from shootout last weekend.
Excited to read the Article !
PROJECT ND: Parts Development, Testing, Measurements, DYNO
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 78
- Joined: Tue May 24, 2016 10:32 am
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Brian, quick cosmetic question for you. Does the Velox diffuser hide the resonator on the long tube mid-pipe? I was considering modifying the mid-pipe to make it sit higher by replacing the resonator with a Burns SS muffler ($350-$550). If the diffuser hides it when looking at the rear of the car, I'd rather go that route than hack up the exhaust. The diffuser would be the same cost range as the Burns muffler, plus I'd get the added aero benefits and a nice look.
2017 Meteor Gray Club
-
- Posts: 78
- Joined: Tue May 24, 2016 10:32 am
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Quick note to that. I have the SSTT muffler, so the diffuser would have to sit in it's absolute lowest position.
2017 Meteor Gray Club
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Good question, do not currently have the Velox item on our car (had it off for playing with numerous muffler mods) so best I can say is that I imagine it would help hide the resonator from some angles... but how much I cannot recall at this moment.
Go to the Velox description on our site and see the low angle pics, including the pic below, and you can still see the resonator pretty clearly...but shooting up from the ground. Looking at these shots I expect that from eye level with the muffler tip the resonator is mostly hidden.
Go to the Velox description on our site and see the low angle pics, including the pic below, and you can still see the resonator pretty clearly...but shooting up from the ground. Looking at these shots I expect that from eye level with the muffler tip the resonator is mostly hidden.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 497
- Joined: Fri Oct 17, 2014 11:37 pm
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Photo from SEMA 2016 when we visited ACT's booth and the new ND clutch was on display. This clutch and a complimentary flywheel are still not quite in production but we now have pre-production units here from ACT to begin testing with!
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
This ACT Clutch and ACT Light Flywheel is now installed in our ND for testing. First impressions is that pedal pressure very close to stock, just slightly heavier (which is good). With any light flywheel there is the expectation of a little increase in vibration because the flywheel is a big spinning dampener and as the weight gets lower the vibrations will climb. I didn't notice the increased vibrations in the first drive, which was lower rpms. On the second drive, spinning it to redline I did notice some increased vibrations from roughly 6000 rpms and up.Ryan @ GWR wrote:Photo from SEMA 2016 when we visited ACT's booth and the new ND clutch was on display. This clutch and a complimentary flywheel are still not quite in production but we now have pre-production units here from ACT to begin testing with!
Notes on weight above picture.
We are READY for BOOST!
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 78
- Joined: Tue May 24, 2016 10:32 am
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Do they plan to make an aluminum option to cut that weight down some more? I'm planning to stay NA, so lighter would be my priority in a clutch kit.
2017 Meteor Gray Club
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Fidanza and other flywheel makers will do aluminum, but ACT prefers steel. This is their "StreetLite" and they might do a "Prolite" version...which would still be steel but another 2 to 3 pounds less weight. From driving this Streetlite my feeling today is that I would not want lighter, the anticipated additional vibrations would get annoying.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 78
- Joined: Tue May 24, 2016 10:32 am
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
Thanks, Brian. That's disheartening. I was hoping to knock a few extra pounds off when it came time to change the clutch to help liven up rev characteristics.
2017 Meteor Gray Club
Re: PROJECT ND: Parts Development, Testing, Measurements, DY
A little autocross fun testing the flywheel and clutch, worked great.....
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com