PROJECT FIAT 124, Testing, Measurements, Dyno, etc
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
Tork MotorSports reflash of stock ECU working well. Love E85 for cooling benefits on hot autocross and track days, it's race gas for cheap with effective octane 105 and better.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
GT4 Testing at Monza.
FULL Aero, wish we had that much for track days!
FULL Aero, wish we had that much for track days!
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 70
- Joined: Sun Jul 23, 2017 1:21 am
- Location: Brisbane, Australia
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
looks like the old Mitsubishi 3000GT!
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
Fiat SportCats Shipping TODAY!
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 70
- Joined: Sun Jul 23, 2017 1:21 am
- Location: Brisbane, Australia
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
Just wondering - why do you 'only' run a 17 inch wheel vs an 18?
Wouldn't the extra tyre 'stiffness' / lack of sidewall flex be a positive - is the weight gain that much of an issue?
Wouldn't the extra tyre 'stiffness' / lack of sidewall flex be a positive - is the weight gain that much of an issue?
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
Look around for a light 4x100 18 wheel, there are about zero choices and nothing 8 or 9 inches wide. And that's just the wheels, choice in tires in right diameters also close to nothing. The NC gen chassis was the only Miata that was 5 lug so it does get raced with 18 inch because there are some good wheel choices that fit that generation.
Even wide 17 inch is a Unicorn, love our 17x9 6UL wheels but what I need next is 17x9.5 or 17x10 in 4x100 and that doesn't exist outside of custom order at $600 per wheel. We stock 17x10 in 5 lug for NC generation (shown on my old 2.5 liter NC below) and I could use lug conversion to get that on the Fiat and ND projects but I don't like the weight or complexity of the conversion. Nonetheless, Fiat would be faster if Hoosier 245mm tires were spread on something wider than 9 inch wheels we are using now.
Even wide 17 inch is a Unicorn, love our 17x9 6UL wheels but what I need next is 17x9.5 or 17x10 in 4x100 and that doesn't exist outside of custom order at $600 per wheel. We stock 17x10 in 5 lug for NC generation (shown on my old 2.5 liter NC below) and I could use lug conversion to get that on the Fiat and ND projects but I don't like the weight or complexity of the conversion. Nonetheless, Fiat would be faster if Hoosier 245mm tires were spread on something wider than 9 inch wheels we are using now.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
-
- Posts: 70
- Joined: Sun Jul 23, 2017 1:21 am
- Location: Brisbane, Australia
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
Makes sense - actually now you mention it I remember reading some hype about the change back to 4 lug pattern and how it would open the Nd up to more traditional "small car" aftermarket wheel choices, too bad that didn't help with sizing as much as styling
The 18's on the NC look great - normally I don't love the look of that wheel (I'm a fan of them functionally - light weight and whatnot), but in an 18 they suddenly become a really good looking wheel - especially so on the NC!
The 18's on the NC look great - normally I don't love the look of that wheel (I'm a fan of them functionally - light weight and whatnot), but in an 18 they suddenly become a really good looking wheel - especially so on the NC!
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
BMW likes the Fiat 124 enough to crib much of the design detail for the next Z4.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
As we are putting down more power on the car.
How is tranny and diff holding up?
Is it time to develop a cooler for the tranny and diff?
How is tranny and diff holding up?
Is it time to develop a cooler for the tranny and diff?
Re: PROJECT FIAT 124, Testing, Measurements, Dyno, etc
klikai wrote:As we are putting down more power on the car.
How is tranny and diff holding up?
Is it time to develop a cooler for the tranny and diff?
Busy moving company into new building, zero free time to get to the dyno until we get out of boxes. Today was stuff like get the lobby metal work up, knock out another wall for Ryan's product development area, locate an A/C duct over Sean's office, etc.
No issues with tranny and diff. E85 tune feels a lot faster. We know from using this trans in the NC that it is good to 300 hp without adding cooling (remember this is NOT a delicate ND Skyactiv transmission, Fiat went with proven NC transmission). To put it another way, I still race our 2007 NC Miata with 320 at the wheels, no fluid cooler for that trans so I don't expect it will ever be 'time' to develop fluid cooler on the Fiat 124. With the NC an air scoop was enough for our extreme 'NC LIGHT', with scoop shown one page back on the Fiat 124 compressing more air on the engine cast finned oil pan and trans the temps are holding steady for both engine oil and trans at our SCCA HOT Summer competition days. Will get that scoop to market in the next few months. If we can be happy on heat levels with simple air scoop then no good reason to do fluid cooler that adds massive costs and complications, additional points of failure, etc.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Good-Win Racing
www.good-win-racing.com