Maverick the Shop Truck!

Welcome to the Good-Win Racing Forum. Feel free to tell us who you are, leave any comments or suggestionson how we can serve you better
Brian
Site Admin
Posts: 10755
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Re: Maverick the Shop Truck!

Post by Brian »

First picture with prototype Progress Lowering Springs.

What's different from the Eibach Springs? The Eibach Maverick Springs are a really good experience, loved the look and those will be THE choice for customers wanting max lowering springs and front to rear heights as perfectly level as possible without going with much more expensive coilovers. With the Eibach springs we are half inch into the front bumpstops at all times unless we trim the front stops, which is called for in the Eibach instructions. We have the Eibach choices on the site, click here for lots more detail on those and current ship status.

But we want also want a choice that does not require bumpstop trim. So, the first change is the Progress Springs are made to use with STOCK bumpstop, no trim needed. That makes install easier and has other benefits we think some customers will appreciate. This means we are slightly higher... but we keep full bumpstop performance, truck free rides when going straight and is above the factory bumpstops until you turn the wheel, at which point we have much smoother transition into using the bumpstops as a progressive spring in the turns. Result is smoother down the freeway and over freeway joints and really under all conditions and quick gain in rate as you load it into a turn. Our Miatas are designed from the factory to work this way, you use the bumpstops as soon as you turn the wheel but you are just at the top tip of them until you turn that steering wheel (and decades ago the Porsche 944 was one of the first Sports Cars to use bumpstops in this manner).

Progress Springs also have a bit of rake with the goal of keeping more 'truck like' usefulness, you can load the bed and result is level, also keeps geometry better for towing moderate loads like our aluminum trailer with race car. When you go to Home Depot with these springs and load some garden mulch in the bed it won't be doing a Carolina Squat.
ProgressMaverickLowered.jpg
ProgressMaverickLowered.jpg (1.11 MiB) Viewed 305 times
Finally, we have little to no dead coil stack, and the Eibachs have about five dead coils. Some dead coils are needed because they keep the spring seated when truck gets some air over potholes and railroad tracks, but we like to keep it minimal for lowest unsprung weight and best travel without coil bind, etc.

FRONT Progress
MaverickFrontProgress.jpeg
MaverickFrontProgress.jpeg (190.31 KiB) Viewed 303 times
REAR Progress
ProgressMaverickRear.jpeg
ProgressMaverickRear.jpeg (133.15 KiB) Viewed 303 times
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Brian
Site Admin
Posts: 10755
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Re: Maverick the Shop Truck!

Post by Brian »

Because trucks get used extra hard, the Progress Springs for Maverick will use Dual-coat powder coating!
 

The process uses two coatings developed for superior corrosion resistance & impact durability.

First coat is a zinc-rich primer

Second coat is a TGIC polyester top coat

Both layers are bonded together during the curing process in a microprocessor-controlled conveyor-oven.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Brian
Site Admin
Posts: 10755
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Re: Maverick the Shop Truck!

Post by Brian »

Lowered Maverick with lots of other fun added by Mark Austin.
Attachments
Mavericks!.jpg
Mavericks!.jpg (408.51 KiB) Viewed 163 times
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
JohnG595
Posts: 6
Joined: Wed Nov 23, 2022 7:09 am
Location: Metro Detroit

Re: Maverick the Shop Truck!

Post by JohnG595 »

Hello fellow Goodwin!

I’ll admit. I came here just for this thread. I do love Miata’s, but don’t fit well in them (fat guy in little coat).

Looking forward to seeing the results of the in house springs. Seeing the shop truck pictures and knowing your expertise it’s a pretty easy choice to follow suit. Bring on the low!
Attachments
786C841F-4EDB-4FC2-93AD-E86A351F5E87.jpeg
786C841F-4EDB-4FC2-93AD-E86A351F5E87.jpeg (310.83 KiB) Viewed 141 times
John Goodwin (no relation)
@SLWKRT (Instagram)
Brian
Site Admin
Posts: 10755
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Re: Maverick the Shop Truck!

Post by Brian »

JohnG595 wrote: Wed Nov 23, 2022 7:15 am Hello fellow Goodwin!

I’ll admit. I came here just for this thread. I do love Miata’s, but don’t fit well in them (fat guy in little coat).

Looking forward to seeing the results of the in house springs. Seeing the shop truck pictures and knowing your expertise it’s a pretty easy choice to follow suit. Bring on the low!
Welcome John!
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Brian
Site Admin
Posts: 10755
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Re: Maverick the Shop Truck!

Post by Brian »

First Pictures LIFTED with Progress Prototype lift springs for Maverick!
245/65R-17 Falken WildPeak A/T Trail SL on 17x7.5 Sparco Dakar wheels in 35mm offset.
Attachments
SparcoMaverick.JPG
SparcoMaverick.JPG (528.99 KiB) Viewed 93 times
mav88.JPG
mav88.JPG (1.95 MiB) Viewed 94 times
mav8.JPG
mav8.JPG (2.19 MiB) Viewed 95 times
mav5.JPG
mav5.JPG (3.08 MiB) Viewed 95 times
maverickoffroadlook.JPG
maverickoffroadlook.JPG (2.68 MiB) Viewed 97 times
MaverickLiftedATtires.JPG
MaverickLiftedATtires.JPG (1.81 MiB) Viewed 126 times
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
Brian
Site Admin
Posts: 10755
Joined: Tue Feb 15, 2005 11:44 am
Location: San Diego CA
Contact:

Re: Maverick the Shop Truck!

Post by Brian »

I forgot how SLOPPY the AT tires feel. Suspension still feels pretty flat with these springs and our big rear sway bar but the A/T tires with big sidewalls on narrower wheels feel much more sloppy than my lowered setup with 18x8.5 and 235/60/18. This is development fun, but will go back to the lowered truck that I prefer after we put some development time on this setup.
Brian Goodwin
Good-Win Racing
www.good-win-racing.com
JohnG595
Posts: 6
Joined: Wed Nov 23, 2022 7:09 am
Location: Metro Detroit

Re: Maverick the Shop Truck!

Post by JohnG595 »

The combo looks fantastic. I guess the benefits of California is ample places to test and good weather for it too. Can’t wait for the finished products.
John Goodwin (no relation)
@SLWKRT (Instagram)
Post Reply