I am upgrading the engine mounts with AWR 70.
The middle (joint) bolt in the mount is needs to be tighten after the install, anyone can share what the torque should be on it?
Any other informtion or points, lessons learned regarding the install will be helpful.
Thanks in advance
Installing/upgrading Engine Mounts
Hi There Arrow - I did write a little on the Miata.net - if you go there - please do a search.
Its actually simple - I can give you a few pointers.
If you have a FSTB remove it first or your Engine will not rise high enough.
Put the car on jack stand (not the jack- safety first)
Put a jack under the oil pan - don't worry - or similar point.
remove the wheels.
There are plastic covers which will be in the way - easy to remove - one turn with the philips head screw and they pop out - you'll see them when you look towards the mount from the wheel well.
Then raise the engine - loosen the bolts and the mount will just drop off.
I have a good jack with a 5" round rubber pad - you can use a wood block or something.
You can do both at the same time or one at a time.
easy stuff- should take less then two hours.
Go for it - - you'll be fine.
Its actually simple - I can give you a few pointers.
If you have a FSTB remove it first or your Engine will not rise high enough.
Put the car on jack stand (not the jack- safety first)
Put a jack under the oil pan - don't worry - or similar point.
remove the wheels.
There are plastic covers which will be in the way - easy to remove - one turn with the philips head screw and they pop out - you'll see them when you look towards the mount from the wheel well.
Then raise the engine - loosen the bolts and the mount will just drop off.
I have a good jack with a 5" round rubber pad - you can use a wood block or something.
You can do both at the same time or one at a time.
easy stuff- should take less then two hours.
Go for it - - you'll be fine.
Hey Cyber, i read all your posts at miata.net and got a good idea of what to do, but there are still some missing spots for me that i didnt fully understand. I hope you don't mind if i write out a theoretical guide and then maybe you can correct me?
1. Put the car into gear and apply handbreak to keep the car from moving.
2. Jack the front of the car up with one stand on each side of the car towards the front tires.
3. Remove front tires.
4. Apply jack under the oil pan with a piece of wood on jack to distribute the surface area. Jack until it is tightly under the oil pan without lifting the engine.
*this is where im mostly confused*
5. Loosen mounting on either side from the wheel well(just one at a time), then slightly jack the engine up to remove the old motor mount.
6. Replace with new mount and lower engine just a little bit to line up holes? Use proper torque numbers.
7. Proceed to second mount on other side, untighten all its screws.
8. Slightly lift engine again to wiggle out the old motor mount.
9. Replace with new mount and lower engine just a little bit to line up holes? Use proper torque numbers.
10. Now that both motor mounts are replaced, slowly lower the jack under the engine.
11. Put wheels back on and un-jack the car.
Is this the proper theoretical procedure? Please correct me anywhere and add anything else needed.
1. Put the car into gear and apply handbreak to keep the car from moving.
2. Jack the front of the car up with one stand on each side of the car towards the front tires.
3. Remove front tires.
4. Apply jack under the oil pan with a piece of wood on jack to distribute the surface area. Jack until it is tightly under the oil pan without lifting the engine.
*this is where im mostly confused*
5. Loosen mounting on either side from the wheel well(just one at a time), then slightly jack the engine up to remove the old motor mount.
6. Replace with new mount and lower engine just a little bit to line up holes? Use proper torque numbers.
7. Proceed to second mount on other side, untighten all its screws.
8. Slightly lift engine again to wiggle out the old motor mount.
9. Replace with new mount and lower engine just a little bit to line up holes? Use proper torque numbers.
10. Now that both motor mounts are replaced, slowly lower the jack under the engine.
11. Put wheels back on and un-jack the car.
Is this the proper theoretical procedure? Please correct me anywhere and add anything else needed.