Help me decide what this is.
Help me decide what this is.
The small box right on top of the trans tunnel. Is it the airbag system computer? My car is on a serious diet right now.
- Attachments
-
- Car.jpg (55.52 KiB) Viewed 3251 times
2007 NC, 6spd. True Red, BEGi turbocharged. Supporting mods.
Re: Help me decide what this is.
Not 100% sure but I believe it is the Yaw sensor for the DSC system
Re: Help me decide what this is.
It's the SAS Control module.
It contains the shock sensor which decides if an impact is serious enough to deploy airbags and seat belt tensioners.
It also monitors the system to ensure bags don't deploy if a fault occurs.
SAS CONTROL MODULE REMOVAL/INSTALLATION
2007 Mazda MX-5 Miata Sport
2007 RESTRAINTS Air Bag System - MX-5 Miata
1. Perform SAS control module configuration when replacing it. (See SAS CONTROL MODULE
CONFIGURATIONS .)
2. Turn the ignition switch to the LOCK position.
3. Remove the battery cover.
4. Disconnect the negative battery cable and wait for 1 min or more . (See BATTERY
REMOVAL/INSTALLATION [LF] .)
5. Remove the following parts:
1. Console (See CONSOLE REMOVAL/INSTALLATION .)
2. Side wall (See SIDE WALL REMOVAL/INSTALLATION .)
3. Console panel (See CONSOLE PANEL REMOVAL/INSTALLATION .)
6. Remove in the order indicated in Fig. 18 .
WARNING: Handling the SAS control module improperly can accidentally
deploy the air bag modules and pre-tensioner seat belt, which may
seriously injure you. Read the air bag system service warnings and
cautions before handling the SAS control module. (See AIR BAG
SYSTEM SERVICE WARNINGS .) (See AIR BAG SYSTEM SERVICE
CAUTIONS .)
CAUTION: Handling the SAS control module improperly can accidentally deploy
the air bag modules and pre-tensioner seat belt, which may seriously
injure you. If configuration is not completed before removing the SAS
control module, DTC B2477 will be displayed.
2007
It contains the shock sensor which decides if an impact is serious enough to deploy airbags and seat belt tensioners.
It also monitors the system to ensure bags don't deploy if a fault occurs.
SAS CONTROL MODULE REMOVAL/INSTALLATION
2007 Mazda MX-5 Miata Sport
2007 RESTRAINTS Air Bag System - MX-5 Miata
1. Perform SAS control module configuration when replacing it. (See SAS CONTROL MODULE
CONFIGURATIONS .)
2. Turn the ignition switch to the LOCK position.
3. Remove the battery cover.
4. Disconnect the negative battery cable and wait for 1 min or more . (See BATTERY
REMOVAL/INSTALLATION [LF] .)
5. Remove the following parts:
1. Console (See CONSOLE REMOVAL/INSTALLATION .)
2. Side wall (See SIDE WALL REMOVAL/INSTALLATION .)
3. Console panel (See CONSOLE PANEL REMOVAL/INSTALLATION .)
6. Remove in the order indicated in Fig. 18 .
WARNING: Handling the SAS control module improperly can accidentally
deploy the air bag modules and pre-tensioner seat belt, which may
seriously injure you. Read the air bag system service warnings and
cautions before handling the SAS control module. (See AIR BAG
SYSTEM SERVICE WARNINGS .) (See AIR BAG SYSTEM SERVICE
CAUTIONS .)
CAUTION: Handling the SAS control module improperly can accidentally deploy
the air bag modules and pre-tensioner seat belt, which may seriously
injure you. If configuration is not completed before removing the SAS
control module, DTC B2477 will be displayed.
2007
Rob Young
Black 2005 NCLE GWR Exh, Cosworth, Mototune, Ohlins, PF01
Black 2005 NCLE GWR Exh, Cosworth, Mototune, Ohlins, PF01
Re: Help me decide what this is.
Thanks guys, so essentially key on, unplug battery and then pull it...
2007 NC, 6spd. True Red, BEGi turbocharged. Supporting mods.
Re: Help me decide what this is.
Oh key to LOCK. Don't feel like exploding the airbags...haha
2007 NC, 6spd. True Red, BEGi turbocharged. Supporting mods.